General Requirements
Product/Feature Requirement Specification (Tier 1)
Applicable for all Abaqus products supported on this platform Processor PA-RISC
OS Level HP-UX 11.001
1 Other supported operating systems and versions are listed below under Additional Test Configurations.
Additional Requirements for specific Abaqus Products and Features
Product/Feature Requirement Specification (Tier 1)
Abaqus/CAE, Abaqus/Viewer Graphics Interactive products are not supported on this platform
Building post processing applications (Abaqus make utility with C++) C++ Compiler HP C++ A.03.25
User Subroutines and building post processing applications with Fortran (Abaqus make utility with Fortran and Abaqus user subroutines) Fortran Compiler HP F90 v2.4
Abaqus/Standard & Abaqus/Explicit
MPI based parallel execution		 MPI HP-MPI 1.8.3 (distributed on the Abaqus CD)
Abaqus/Standard & Abaqus/Explicit
MPI-based Distributed Memory Parallel execution		 Interconnect for DMP Distributed memory parallel is not supported on this platform. Use shared memory parallel.
FSI Co-simulation using MpCCI MpCCI
(Fraunhofer SCAI)
 MpCCI Version 3.0.52
Abaqus installation CD-ROM mount -rF cdfs device /cdrom
where device is the CD-ROM device on your system
2SIMULIA intends to qualify and support Abaqus Version 6.6 with MpCCI 3.0.5 and FLUENT 6.3. However, delays with the official release of both MpCCI 3.0.5 and FLUENT 6.3 caused full qualification of FSI Co-simulation to lag the release of Abaqus V6.6.  In the interim, FSI Co-simulation using MpCCI with Abaqus Version 6.6 has been partially qualified using pre-release versions of MpCCI 3.0.5 and FLUENT 6.3. Until qualification can be completed with released versions of MpCCI and Fluent; SIMULIA recommends that interested FSI users continue to use Abaqus V6.5, MpCCI 3.0.4 and FLUENT 6.2.16.  Check back for new information which will be posted here as qualification progresses for FSI Co-simulation.

Additional Test Configurations
Only changes with respect to the Tier 1 configuration are listed.
Tier 2 test configuration
Targeted version
 Requirement Specification (Tier 2)
6.6-2 OS Level HP-UX B.11.11

Requirements to View Online Documentation
Feature Requirement Specification
Abaqus HTML documentation Internet Browser Netscape 7.0, Mozilla 1.2, Firefox 1.0.1, or greater
Abaqus PDF documentation PDF Viewer Not supported. You may be able to view PDF documentation on unsupported platforms using readers available from third parties. See Answer 1599.

Other Platform Notes
Feature Requirement Specification
Abaqus Analysis products Maximum memory accessible
 This platform supports 64-bit addressing, which enables memory usage in excess of 2 GB.
  Patch
  1. The following patches must be installed to read the Abaqus CD-ROM correctly. For details on downloading and installing the patches. See Answer 950.

    For HP-UX 11.00: PHKL_26450, PHCO_26449, PHKL_28060
    For HP-UX 11.11 - v1.0 PA: PHKL_26269, PHCO_25841, PHKL_28025
  2. One of the following HP-UX 11.00 patches must be installed for /usr/lib/libc.sl; this affects all Abaqus products: PHCO_22314, PHCO_23770, PHCO_22076, PHCO_20765, PHCO_24148, PHCO_20555, PHCO_22923, PHCO_27731, PHCO_27774, PHCO_28425
  3. The following HP-UX 11.00 patches are known to be incompatible with Abaqus; if one of these patches is installed, it should be replaced with a compatible patch: PHCO_27608, PHCO_25707, PHCO_18227, PHCO_24732, PHCO_25976.
  4. Patch PHSS_24304 (or comparable) for HP-UX 11.11 (only) is required for User Subroutines and Abaqus/Make.

 

Last Updated On: September 18, 2006 1:22 PM